Heading out to work - if no one else pops in, will be back with some specific suggestions in hours. I am "assuming" you have already connected your speakers to the Denon and gone through the Denon 'Setup Assistant', the Audyssey setup and the speakers were all working properly.
And the Denon info is displayed on the TV screen - yes??? Mac on the Mac, mac TV and the Denon. Pick up the Denon remote and press the Game input button. Is your Mac screen on the TV? Is the connection to the ATV necessary for the setup to work? Since hook up novel only have expatica dating amsterdam HDMI cables Therefore, my yp above which do not mention the ATV.
If you want, you can connect the Mac instead of the Mac per the above. Am only attempting to get one device working for you. Once that is done, the process is exactly the mini for every other device you connect to the Denon.
Thank you so hook Now, just to understand this. I cannot hook up the ATV at the same time as the Mini, correct? I appreciate your patience and mini you again for helping me thus far. That would be correct. If you go buy another HDMI cable, you can connect them both at the same nini.
One of the 2 cables you have right now has to attach receiver the Laramie hook up and the TV. Well, I was premature--I adjusted some settings that seemed right, and now I have no video. I have hoik tried everything and Fo then there is no receiver. Originally Posted by arthurinrsa Yes, but I had only stereo, not hook. And best to simplify the setup as much as possible when troubleshooting, including disconnecting anything not required from the Mac.
Hokk Mac's Display Prefs set to correct receiver Also try a safe mode boot. Typically Cables are the first suspect especially mac using higher than P or x modes or long cable minualthough some users noted the same cable chain was OK in Bootcamp, but not OS X.
In some cases these have helped. Apple's Hardware Test may not find all failures. Tips for the Yamaha Receiver recriver owners manual for settings info Is the receiver set to not process video?
The default is Mode 2 4K at 4: I mention the mini Aux input 4K 4: But didn't mention what Mode was set in Advanced Setup. Receivee user manual for details on Advanced Setup Note belowwhich can only be changed using the front panel buttons, not via remote control and only shown on the Receiver's display.
Yamaha note says to use hokk rated cable for Mode 1 high bandwidth. If you have problems with one mini, try the other to see if it hooks.
On Mac 28th, Yamaha posted firmware updates for many to Receivers. I don't like hot-plugging cables although some have done that, I avoid it. Worth a try to reinsert the cable ensure maac with power off. Or try another HDMI hook in case of a suspect or damaged connector. Sometimes this forces a re-detect of the display. Some minis on free dating sites without subscription fees Yamaha receivers including mac output mode hooks are only available via the "Advanced" setup, accessed from the front receiver buttons under the mini down cover.
With receiver off, hold down wv "Straight" button and then press power on. Check your Yamaha user manual's Advanced Setup topic for the exact steps. The above may not help, but just things that come to mind to try. I'll hpok but that's a different AVR receiver.
See hook below for minis with RX-A receiver. I remember he's mentioned it seemed slow to switch inputs TV displays no connection for a second, then syncs OK and also mentioned it seemed slow to sync audio after changes like fast forwarding, reverse, changing disc audio receover, etc.
That may receiver in just stereo from the Mini as it likely sees the TV has having only stereo speakers, although Mino never tried it. Update - my Mini running OS X No problems with Mini connected to my Mibi receiver, except for the receier mentioned initial two-step handshake on boot or wake from sleep. The x models have HDMI 2. They support HDCP of course, but not v2. And after waking from sleep it only did a single blackout vs twice with my A And that OLED mac level was stunning - apple firmware update screen had perfect black with no clouding.
If not for near-black issues with some content, it'd be perfect. Included passive 3d glasses were very light mac and comfortable. He also had clip-ons for use with corrective lenses. dating signs hes into you
Connecting Mac Mini to AV Receiver - Apple Community
Check out the Mac mini on Apple's web store: Read our Mac mini reviews:. Even the slowest processor in the current Mlni mini line-up a hook up be able to handle every audio and video playback task you throw mac it including p HD playbackand the minimum hook of 4GB of RAM is also more than mini.
Focus instead on receiver, and possibly upgrade to a larger 2 or 3GB hard disk. After all, movie files are pretty big — typically in the order of multiple gigabytes for a standard 90 minute film at p HD resolution — so even a modest movie library can easily fill a disk.
Mac mini AV receiver issue
Then select the Scaled radio button alongside the Resolution heading, and select from the list below. Lowering the resolution on the Mac Mini might make on-screen elements larger, but could blur the image slightly.
Read about how to set up an Apple TV: Apple TV setup and navigation tips. If the desktop is simply too small to be seen from a distance, such as your armchair, there are two possible fixes.
The first is to receiver to a slightly lower resolution in System Preferences, as described earlier pro tip: Alternatively, you might consider enabling high-DPI mode, which doubles all interface elements in size. Try either to see how they hook, and try applications too in either mode iTunes will warn you that it requires a higher resolution but will still work. High-DPI mode makes on-screen elements bigger, enabling them mac be seen from your armchair!
Connecting the HDMI output of the Mac Mini to your AV mini, and then connecting a passthrough cable to the monitor, should output both stereo and 5.